Nüüd tuli veel ilmsiks ka järgmine "beebiviga", too öhujagamisklapp juhipoolne ei toimi, viga 08. Tuleb ette vötta, tüütu söita ju...palav...külm...palav...külm...
http://blog.saab9-5.com/?p=26 :
B2495
Heater Flap Motor Left. Flap Loose. Note: May set if not calibrated.
Fault symptoms
Perceived temperature in cabin too high or too low compared to the set temperature.
Conditions
The following conditions apply:
• When the control module runs the stepping motor towards an end position and the stepping motor continues more than 20% past the expected end position, the diagnostic trouble code for loose flap is set.
• The diagnostic trouble code can be set if the control module has not been calibrated.
• Continuous monitoring and when calibrating.
Kuna mul köik jupid alles olid, siis otsustasin kasutada seda varianti mida kaasfoorumlane Trionic mainis, 12mm torudeühenduse hülss. Sobib ideaalselt.
Lihvisin originaaljupil toestusrandi maha, hülsile pilu sisse ning et plastik hülsi sees kohe kindlasti pöörama ei hakkaks, fikseerisin selle needivarrega (hiljem see öigesse pikusesse ja EPO taolise liimiga kinni):
- 191515=11122-001.jpg (53.33 KiB) Vaadatud 10999 korda
- 191515=11124-002.jpg (63.09 KiB) Vaadatud 10999 korda
ACC calibration and fault codes - Saab 9-5
Model year 1998-2005
Calibration is done by starting the engine and simultaneously pressing the AUTO and OFF buttons. Calibration takes about 30 seconds. Calibration must be performed if the battery has been disconnected/discharged, if the ACC unit or a stepping motor have been replaced or its position changed.
Calibration is also automatic directly following engine start in the following cases:
new ACC fitted
+30 supply was cut earlier than 10 minutes after the ignition was last turned off (usually in connection with battery replacement).
While calibrating, the number of stored diagnostic trouble codes is displayed instead of the left-hand temperature. Diagnostic trouble codes 0-23 are displayed for 3 seconds each instead of the right-hand temperature.
Name: saab-9-5-acc-calibration.gif
Views: 497
Size: 4.3 KB
- 191515=20451-saab-9-5-acc-calibration.gif (4.91 KiB) Vaadatud 10999 korda
This is a list compiled from WIS documentation
Code Problem OBD
1 Internal control module malfunction B1605
2 Cabin temperature sensor - open or short circuit B1350
3 Solar sensor B1340
4 Mixed-air temperature sensor, LH - open or short circuit B1345
5 Mixed-air temperature sensor, RH - open or short circuit B2345
6 Stepping motor, air-mixing flap, LH - open or short circuit B2490
7 Stepping motor, air-mixing flap, LH - motor jam B2496
8 Stepping motor, air-mixing flap, LH - no mechanical contact with flap B2495
9 Stepping motor, air-mixing flap, RH - open or short circuit B2290
10 Stepping motor, air-mixing flap, RH - motor jam B2296
11 Stepping motor, air-mixing flap, RH - no mechanical contact with flap B2295
12 Stepping motor, air distribution flap - open or short circuit B2400
13 Stepping motor, air distribution flap - motor jam B2406
14 Stepping motor, air distribution flap - no mechanical connection between motor and flap B2405
18 Solenoid valve, heat exchanger shut-off valve - open or short circuit B2375
19 Circulation pump - open or short circuit B2380
20 Ventilation fan B2425
21 DC motor, air recirculation flap - open or short circuit B2410
22 ACC software
23 Sensor Ground B2945
http://saabworld.net/f144/automatic-cli ... 5-a-28199/